A Site for Photographers by Photographers

Community > Forums > Classic Manual Cameras > Took a Ciro-Flex to the Henry...

Featured Equipment Deals

Artistic Animals: Getting the Shot and Postproduction Read More

Artistic Animals: Getting the Shot and Postproduction

Art X gives us some insight into "how he did that" regarding his unique, creative, painterly animal portraits

Latest Equipment Articles

Lensbaby Spark Review Read More

Lensbaby Spark Review

This inexpensive gadget does indeed spark your creativity. Read on to see how.

Latest Learning Articles

26 Creative Photos of Water Drops Read More

26 Creative Photos of Water Drops

These absolutely amazing macro photographs feature a tiny elemental thing that can hold a lot of mystery. Take a moment to enjoy these photographs of water drops.


Took a Ciro-Flex to the Henry Ford Museum...

Doug Grosjean , Feb 20, 2006; 04:16 p.m.

Hi all,

I took a Ciro-Flex to the Henry Ford Museum this past Saturday. My girlfriend lives near there, so we have a membership, and I like to take my son there as well.

I've been experimenting with panoramic stitching, and noticed that the tripod socket on the side of the Ciro-Flex looks to be almost right where I would estimate the nodal point to be. So, I set up a series of 4 shots of Bucky Fuller's Dymaxion house, to be stitched together back home.

Responses


    1   |   2     Next    Last

richard oleson , Feb 20, 2006; 04:18 p.m.

Neat photo, Doug! i'll bet it looks terrific at a larger scale.

:)=

Doug Grosjean , Feb 20, 2006; 04:19 p.m.

The stitching went perfectly - better than any other camera I've tried that technique with. Somehow I doubt the location of that socket is accidental.

After that, a look at a stationary steam engine, used to power other machinery. What's interesting is that the machinery went through a phase where it was "styled" - note the lines and shapes and curves in the photo. Another engine next to this one has Gothic arches, and looks much like a cathedral....


Steam Engine Details

Doug Grosjean , Feb 20, 2006; 04:22 p.m.

On the backside of the steam engine, there was a steam-powered portable boring bar on display. I only know what it is because I read the plaque. Long ago I used a boring bar on small engines, but it sure didn't look like this. A plaque tells that the portable unit saved downtime, allowing mechanics to make a cylinder new again, on site.


Steam Powered Boring Bar

Doug Grosjean , Feb 20, 2006; 04:25 p.m.

And of course there's many interesting autos there as well. Here's the backside of a Model T Ford prepared for an early Indy 500 race. It wasn't raced - it was entered and rejected for being "too light". Henry Ford replied that he built race cars, not trucks, and didn't enter again. This is all in polished aluminum, and is gorgeous.... My Dad still has a pair of Model T's; I shot the back because I already have a front view of the same car. This one was sort of for my Dad.


Model T - Indy Car

Doug Grosjean , Feb 20, 2006; 04:27 p.m.

Next to the Model T is a couple relatively modern Indy-type cars....


Modern Indy Cars...

Doug Grosjean , Feb 20, 2006; 04:28 p.m.

Then a classic MG, posed next to a Ford street rod:


MF and Ford

Doug Grosjean , Feb 20, 2006; 04:30 p.m.

Then finally, a modern Ford endurance racer. A similar street-legal car, with identical styling and a 500 HP engine, is a production car now. I've seen one in my life, in my girlfriend's Dearborn neighborhood with Manufacturer's Plates on it.


Ford GT

Doug Grosjean , Feb 20, 2006; 04:34 p.m.

And that was my Saturday, lugging a tripod and an old camera and a young son around the Henry Ford museum.

Don't know if I need to get a life, or if I have a wonderful life already.

Just kidding - I *do* know the answer to that question.

Thanks for letting me share here - enjoy!

Doug

PS - Rick, thanks for the compliment! It does look good, but... it could be better. I didn't use a small aperture for the Dymaxion shots, as people were passing through all the time - so it's not quite as sharp as I'd like. And the shiny aluminum skin reflected light in strange ways - but now I know the technique works well using that side-socket, and next time I'll do better. The learning never ends, right?

Doug Grosjean , Feb 20, 2006; 04:38 p.m.

I meant "Thanks, Richard".

I work with a Richard who goes by Rick, and so made a slip.

Doug


    1   |   2     Next    Last

Back to top

Notify me of Responses